Bookmark
Fullscreen
Exit fullscreen
success

Well done!

Close
  • Introduction

    If you have already acquired the diabetes manager together with the Accu-Chek Spirit Combo insulin pump, the two devices will already have been paired. If you acquired the devices separately or after a Warning W10: Bluetooth® FAULT, you must pair the devices before they can communicate with each other. When Pairing your Accu-Chek Spirit Combo insulin pump with the Accu-Chek Combo diabetes manager, place both devices on a table or desk, so that you can see the displays of both devices clearly. You should not perform the pairing process in crowded areas, since electronic signals from other devices could interfere with the pairing process.
    Let's see how to pair the devices.

    Next lesson
    Software
  • Goals

    At the end of this lesson you will know how to:

    • Pair the pump and diabetes manager using Bluetooth® wireless technology
    • Remove a paired device

    Let's start with learning how to pair the pump and diabetes manager.

    Next lesson
    Software
  • Pairing procedure: step 1

    • Press Icon to move to the Bluetooth® SETTINGS screen
    Next lesson
    Software
  • Pairing procedure: step 2

    • Press Icon to select the ON/OFF screen
    • Press Icon or Icon to switch on the Bluetooth® function

    When Bluetooth® wireless technology is turned off, you cannot access the PAIRED DEVICE menu.

    Next lesson
    Software
  • Pairing procedure: step 3

    • Press Icon to move to display the PAIRED DEVICE screen
    • The pump screen indicates that a device is already paired. You have to delete the old pairing first
    • If the pump screen indicates that no paired device is available, activate Bluetooth® wireless technology on the diabetes manager by placing it into pairing mode by holding down Icon and simultaneously pressing Icon
    Next lesson
    Software
  • Pairing procedure: step 4

    • Press the Icon on the pump and see the Add Device screen
    • Press the Icon to initiate pairing

    The pump starts searching and detects the diabetes manager, displaying its serial number. This process may take several minutes.

    Next lesson
    Software
  • Pairing procedure: step 5

    • Press Icon or Icon to select the serial number, which is also shown on your diabetes manager screen
    • Press Icon on the pump to confirm that you want to pair the diabetes manager
    Next lesson
    Software
  • Pairing procedure: step 6

    • The pump begins the pairing process and then shows a 10-digit code
    • Enter the code on the diabetes manager display, using Icon, Icon and Icon and then Icon to move to the next digit
    • Confirm the complete code with Icon
    Next lesson
    Software
  • Pairing procedure: step 7

    • After the pairing is completed press Icon to turn the diabetes manager off
    Next lesson
    Software
  • Pairing procedure: step 8

    • The pump now shows the PAIRED DEVICE screen
    • Press Icon to confirm the pairing
    Next lesson
    Software
  • Pairing procedure: step 9

    • The pump displays the PAIRED DEVICE screen
    • You can return to the RUN screen by pressing Icon

    If the pairing is not successful at the first attempt, wait a few minutes before you repeat the procedure in a less crowded environment.

    Next lesson
    Software
  • Troubleshooting the connection: removing a paired device

    In case of problems with the Bluetooth® connection, you have to repeat the pairing procedure described here. Since only one diabetes manager at a time can be paired with your pump, you must delete the old pairing before you can pair your pump with a new diabetes manager. Here's how.

    Next lesson
    Software
  • Removing a paired device: step 1

    • Press Icon to move to the Bluetooth® SETTINGS screen
    Next lesson
    Software
  • Removing a paired device: step 2

    • Press Icon to enter the Bluetooth® ON/OFF screen
    Next lesson
    Software
  • Removing a paired device: step 3

    • Press Icon to move to the PAIRED DEVICE screen
    Next lesson
    Software
  • Removing a paired device: step 4

    • Press Icon to move to the DELETE DEVICE screen
    • Press Icon once to delete the pairing and a second time to confirm

    To remove a paired device, you don't need to delete the pairing on the diabetes manager.

    Next lesson
    Software
  • Now it's your turn! try to pair the demo pump with the demo diabetes manager.

    Click on the demo diabetes manager buttons to practice what you have just learnt. If you decide to practice any functions on your own Insulin pump or diabetes manager, make sure the infusion set is disconnected from your body so that there is no chance of accidental insulin delivery. Ensure all your settings are put back to where they should be at the end of the practice.

    Next lesson
    Software
  • Quiz

    Which buttons do you have to press simultaneously to switch on the diabetes manager's Bluetooth® connection?

  • Quiz

    You can have more than one diabetes manager connected to a pump at the same time.

  • Congratulations!

    You have completed the pairing your pump with your diabetes manager section.

    Next lesson
    Software

Bookmark

Module / Chapter

Lesson - 5

Page added to bookmark